GO TO PAGE     |  1  |  2  |  3  |  4  |  5 |  6  |  7  |  8  |  9  |  10  |  11  |  12  |  13  | [  Page 2  ]
 
Simple to Order
Using the table below, select the part number for the particular cable diameter and formation required. For example: an outside cable diameter of 33mm in trefoil formation is Part No VRT-03 which covers a cable diameter range from 30 to 35mm. The VRT-03 cleat can also be used for single cables between 49 and 64mm in diameter.

Extensive Diameter Range
The standard trefoil cable-cleat range accommodates diameters from 23-85mm. The standard single cable-ceat accommodates diameters from 33-153mm. For applications outside the ranges shown, please contact the Ellis Patents Sales Department for further assistance.
  
Part No
  
VRT-01
VRT-02
VRT-03
VRT-04
VRT-05
VRT-06
VRT-07
VRT-08
VRT-09
VRT-10
VRT-11
VRT-12
VRT-13
VRT-14
VRT-15
VRT-16

Trefoil Cable
Min Dia.
mm
Formation
Max Dia.
mm
23 28
27 32
30 35
33 38
36 42
40 46
44 50
48 55
51 58
55 62
59 66
63 70
67 74
71 78
74 82
77 85

Single Cable
Min Dia.
mm
Formation
Max Dia.
mm
33 50
43 58
49 64
55 70
58 75
63 84
73 90
83 100
88 104
86 110
90 115
100 125
107 132
120 145
125 150
132 153
Dimensions
  
W (Max)
mm 		  
H (Max)
mm 		  
P
mm 		  
D1
mm 		  
D2
mm
67 93 25 10 10
73 101 25 10 10
78 107 25 10 10
84 113 25 10 10
95 118 50 10 10
100 125 50 10 10
108 135 50 10 10
118 144 50 10 10
122 149 50 10 10
136 154 75 10 10
140 163 75 10 10
148 171 75 10 10
156 178 75 10 10
164 187 75 10 10
172 193 75 10 10
178 199 75 10 10
Quadrafoil Application

Please contact the Ellis Patents Sales Department for further assistance.

Installation Instructions

  • Remove the nyloc nut and washer from the M10 set screw
  • Prise out the base pad and bolt the cleat to the supporting structure using single or two bolt fixing as required, replace the pad
  • Fit the cables into the cleat and flex the arms of the cleat around the cable by pulling the flanges. Refit screw, nut and washer and tighten the nyloc nut
  
Maximum Fault level
kA RMS 		Recommended spacing of cleats
(metres)
tested for 0.1 seconds on straights on bends
43kA 0.9 0.3
Dimension Codes
W
H
P
Width
Height
Hole Pitch
D1
D2
D1
Hole Diameter (two bolt fixing)
Hole Diameter (single bolt fixing)
All Vulcan are 54mm deep

GO TO PAGE     |  1  |  2  |  3  |  4  |  5 |  6  |  7  |  8  |  9  |  10  |  11  |  12  |  13  | [  Page 2  ]
                  
 
    |  EYE  |  LEGRAND |  SCAME  |  WHEATLAND  |  HAZLUX  |  WEBER  |  BUSSMANN  |